Відео

Thanks for the video. Do you have the link to purchase the door handle?

Do you really need that washer? The big one? Cause I tried reversing it, but it causes friction for my pulley and won’t let it spin when it’s bolted down

Great video!!! I need to take my exhaust off to sort some rust issues and i just assumed that I would be fighting with the rubber mounts, bolts are much easier! Thanks

Is the ride more stiff with these ?

100% worked bro! Thank you sir

Damn, I wish my G35 was that clean on the bottom. From the rust belt - Alberta, Canada

Old vid I know but for those who do this and want to save a lot of time. Use denatured alcohol with a stiff bristle toothbrush to remove the rubbery black paint. Much easier! Gets you straight to the gray paint layer without creating deep scratches and ruining loads of sandpaper. The denatured alcohol literally starts melting that rubbery paint without damaging the ABS plastic or gray paint layer. Just pour some denatured alcohol in a glass jar, dip your brush and work it into the piece. It takes a few seconds to get started, but once you break through to the gray paint underneath it starts to make short work. I’ve also used this method with good success on the center waterfall and shifter bezel (textured pieces), best way I know of removing the OEM paint without destroying that factory texture.

You only need to remove the 22 mm bolt on the ball joint… the knuckle will fall down enough so that you can remove the ball joint, even with the those cups and everything… I am not disagreeing with full throttle. I think Charlie does an awesome job here, but I only removed one bolt and was able to remove and reinstall the entire ball joint without having to takeoff all the other three bolts. Don’t mean to burst anybody’s bubble.

how much lower can the rears go

Love that 10mm socket to remove the plastic clip.

Hey Charlie I just recently tried to replace my oem clutch line to the SS clutch line and I looked up the car where the line meets the hardline and noticed the nut was rounded is there anything you recommend on how to fix it whether it be to replace the nut or the whole entire line ?? Any tip would be appreciated !

Damn….Ive been looking for this for a while.Cant believe a 5yr old video was more helpful then all the other ones I’ve watched

A festival clumsiness!!!!!

Thanks for the video. Guy asked me about doing his windshield yday and I thought I remembered these being really bad. Yea I told him this plastic is 17 years old in Texas and if he wants to remove all this trim I will do the windshield lol. I stay 2 weeks behind so I’m blessed with a lot of work. Been doing autoglass for 38 years and I’ve never liked working on Nissans anyway lol! Thanks again for the video! Have a blessed day!

Great job! i know the struggle im doing the exact same thing except im doing it to a G35

Dope build bro. I’m curious on a vhr swap with all the functions and gauges.

Should the transmission be warm when changing?

Hexa has the worst communication

How much would this cost to do professionally

Need more info on this wiring harness lol

What brand name ball joint did u use

Did you fabricate the bumper yoursel

You put the same oil in diff and trans?

I wouldn’t say in the world 😅🗿🤓🤓☝️☝️😭🤣🤣🤣

Hey quick question I have a 03 G35 Coupe 6MT, body is perfect outside along with perfect paint. Bc coils all around , nice rims only mods. Every suspension component on the rear sub frame is bad all bushings bad differential is bad leaking loose axles they’re connected to the diff , ripped axle boots, an I’m sure the entire front all like ball joints, camber arms all the suspension components are bad, an my engine might be leaking from the Maine seals, car has 145k miles clean tittle. I can’t drive currently do to the rear diff broken, do you recommend I drop the sub frame a replace every parts I can including new diff, an also do the front end? Or sale it as is lol basically redo the entire undercarriage of the car with all new parts an alignment?

I bought a pair for $15 and BOTH of them won’t compress????

Brother 💪🏿💪🏿💪🏿💪🏿 good to see you back. Lol you helped me out so many times over the years with my z. Good to see you holding it down

I forgot I wanted to do the 370 axle/hub swap on my Z until you just mentioned it.

Just picked up my vhr today excited to see the wiring portion

I have an off beat question. With the SPL Solid compression rod, inner front lower control arm and shock bushings will there be a great increase in vehicle nvh in the 350z?

Had to do a double take when youtube recommended me this video as I thought for sure it's an old video. Glad to see new videos and that they are still 350Z related! Cool project btw

What is the size of that ball joint coupling 9:03

Good to see you back but this seems like a lot of work for no real gain🤷‍♂️.... or am i missing something?

Southern California has the best Mexican food. That roach coach does look good

You said the front sway bar was bent? It looked ok.

Did you just use hr harness or?

hello, I love the chain since I got my 350z. I have a question. sometimes my clutch pedal stays stuck for the last 0.4 inch (1cm). Looks like a pedal problem. the clutch is new. apparently a lot of 350z's have this problem but no one really knows what the problem is. did you know what the problem is? thank you 👋

Thanks for this vid! I’m working on these this weekend

Nice,welcome back Charlie!

Thanks for the directions. I did everything you did except adding a new switch. I ended up putting the old regulator back on. I'm still not sure what fixed it, but I think it may have been dirty connectors. Oddly enough, all is working now. I appreciate the detailed instructions. Getting the final bolts back on the door handle pieces was a real pain. I put a little bit of curled paper to guide the bolts back in to the holes, as the ratchet extension alone wasn't working, and I'm still not very good at working on cars in general. Also, I didn't even have to run the reset procedure. Cars are crazy.

do you have to preload it???

Whats your instagram man?? Tons of ftp shops ☠️

Thanks so much for the tips. So simple.

Have a question...you may have a answer to...can i run brembo calipers in front and akebono calipers in the rear on a 350Z nissan? Its about a 1" difference rotor size if i put akebono rotor in the rear

😢 hey dude nice to meet you my g35 making noise like a screeching as im rolling down the road

360z

Hey bro live and sac hoping to be able to get all the stuff I need to go e85 I’ll come give you a visit soon brother

Welcome back Charlie

Couldn't you use independent power to the switch for the window.

Welcome back!